Hi Cliff,
Yes, the Blue Ox Base Plate Kit # BLU23XR is part number BX2692 and would be a fit for your 2024 Ford Bronco whether you have the Performance Heavy Duty Modular Bumper or standard plastic bumper. If you haven't picked out the rest of your flat towing components then I have the following recommendations:
Tow Bar: etrailer SD Non-Binding Tow Bar for Blue Ox Base Plates # e47ZR. This tow bar comes with safety cables included as well as an adjustable head to help keep it level between... view full answer...
Hey David, thanks for the picture. I was able to track down a spec sheet for your Dexter axle which I have included below. The 031-029-02 bearing is item # 15123 and the 031-030-02 bearing is item # 25580. For a bearing kit you can use part # BK3-110 which will come with both bearings, races, grease seal, spindle washer and cotter pin. view full answer...
Hi Nichole,
The Hidden Hitch by Draw-Tite Trailer Hitch Receiver # DT38GR doesn't come with a wire harness included so you would need to pick up the Tekonsha T-One Vehicle Wiring Harness # 118467 for your 2015 Subaru Outback. This wire harness will only take a few minutes to install, just pull up a few pieces of trim in the rear hatch area and plug it right in. I've attached a video below where Randy will walk you through the installation process. view full answer...
The RoadMaster BrakeMaster Custom Seat Adapter # RM33MR attaches to the front seat mounting rails on your 2024 Ford Bronco and gives you a place for the Mounting Post # RM-450596. This post is included with either the Air Brake BrakeMaster # RM-9160 or Hydraulic Brake BrakeMaster # RM-9060. view full answer...
Keith, I'd imagine it's because it's not a super common setup. I'd recommend just swapping the axles/hubs with the Dexter Trailer Axle w/ Electric Brakes # 6340624-EB which is a bit larger of an axle at 5.2K and has included 5 on 4 1/2 hubs which is way more common. view full answer...
Hello Tim, so the Firestone Air Bag Kit # F2609 will indeed work with your 2024 Chevy Silverado 1500 ZR2 Duramax. Since the ZR2 has a factory 2" lift, you will need the Lift Spacer Kit # F2366 as well.
I have included links to a few of our install videos below. view full answer...
Hi Charles,
I drew up a little diagram below showing the diameter of the Sink Strainer w/ Threaded Basket and Tail Flange for 2" Drain # 3729490-217-022. This strainer requires a 2" diameter drain hole and comes with a rubber gasket to seal the drain. view full answer...
Hey Sue I went ahead and checked, and it does not look like there is a plug and play wiring adapter for your 2024 Subaru Ascent unfortunately.
It looks like in order to use the Tekonsha Primus IQ Trailer Brake Controller # TK90160 you're going to have to use the included universal wiring harness.
You could also use the Curt Echo Wireless Brake Controller # C51180 which plugs into your factory 7 way, so it wouldn't require any splicing or cutting into your wiring. view full answer...
Hello Mark. The RV Flooring Adhesive # TS86FR can absolutely be used for putting rubber coin grip flooring over aluminum. This adhesive can be used for virtually any wood, metal, or concrete surface, and this will include the aluminum flooring in your enclosed car trailer. view full answer...
Hello Andrew. The Tie-Down Kit # TH52FR is not included with the TruXedo Elevate Truck Bed Rack System # TX96NV.
The # TX96NV includes just the Rack itself and the TS Rails. The Tie-Down Kit # TH52FR will need to be purchased separately. view full answer...
Good question Chuck, but you won't actually have to remove the etrailer logo on the Pop & Lock Custom Tailgate Lock with Handle # PL6200.
It won't come with the product, we only put that sticker on for our photos to try and prevent people from using the photos without permission. The # PL6200 you receive will not have a sticker on it. view full answer...
Hey J, for your 2017 Jeep Cherokee I recommend checking out the OptiMate Smart Battery Charger # MA99JR. This is a DC-to-DC charger that will work with flooded, AGM, gel, and LiFePO4 (lithium-iron phosphate) batteries, and has an included weatherproof case with an optional wall mount. view full answer...
The Timbren Silent Ride Suspension # TSR7000T05 will require a 2" x 4 "hollow steel crossmember with 3/16 wall thickness to be welded between the left and right hangers. You will also need to weld the axle seats to the axle. I have included the diagram below for your reference. With a 6" c-channel and 3" crossmembers on top, frame clearance should not be an issue. view full answer...
No, they are not! The locking casters that are included with the Hollywood Racks Rack Valet Rolling Storage Cart for Hitch-Mounted Bike Racks item # HRRV-1 aren't going to work very well in grass. They're designed for hard surfaces. It will be pretty easy to swap them out for larger casters/wheels that will work in the grass.
I have linked the instructions below so you can take a look at how this rack is assembled. view full answer...
Hi Christopher,
The Replacement Support Arm for Thule Omnistor 5200 Motorized Awning # LC62TF should come with two arms and not just one, it will include everything you see in the picture attached below. This comes with two wall brackets to lock the arms in place against the trailer but wouldn't include stakes or anything to anchor it to the ground. There are holes in the feet that you can run some stakes or bolts through, depending on your setup, to secure the arms to the ground. view full answer...
The Easy Grease Trailer Hub and Drum Assembly # AKHD-545-35-EZ-K is designed to be used with 13"-15" diameter wheels. If using steel wheels they can be torqued between 90-120 ft-lbs while aluminum wheels should be torqued between 90-100 ft-lbs. I have included a helpful chart below that you can use as a reference. view full answer...
Hey Bruce I hate to be the bearer of bad news, but unfortunately nothing like that exists on the market currently. All of the RV cameras that are being sold do require the use of a proprietary external monitor.
Just like the Buyers Products RV Backup Camera # 3378883020 you're looking at, it's going to require the use of the included 7" LCD monitor. view full answer...
Yes, the Gen-Y Torsion weight distribtuion shank part # 325-GH-1102 that you reference will work great with your Pro Series weight distribution as it was designed to have same bolt pattern. view full answer...
Hi Russ, thanks for all of the details and photo!
For your application it will be best to get a whole new 14K Equal-i-zer Weight Distribution System w/ 4-Point Sway Control # EQ37140ET. When I sent your photo over to my contact at Equal-i-zer he said there are a few things that are concerning like the shank is not one that came with the hitch head and there is some hardware missing like the sleeves where the bars install on the hitch system.
Getting a whole new system gives you a whole... view full answer...
Based on the specs of the Lectric XP 3.0 and the fact that you'll be installing this on flat towed vehicle I have to recommend the Yakima OnRamp Bike Rack for 2 Electric Bikes # Y36FR. It has a 66lb per bike capacity to accommodate your 57lb bikes (never haul the bikes with the batteries installed, they should always be stored inside of the vehicle). The trays accommodate up to 3.25" wide tires so they'll work with your 3" wide tires. The padded clamps can easily adjust around to grip the... view full answer...